How to Assemble 4 Post Car Lifts

  Before installing your new lift, you must follow the manufacturer's instructions carefully. In this article, you will learn how to assemble 4 post-car lifts. The installation process will vary depending on the brand and model of lift you purchased. The following steps will help you assemble your new lift in no time at all. […]

 

Before installing your new lift, you must follow the manufacturer's instructions carefully. In this article, you will learn how to assemble 4 post-car lifts. The installation process will vary depending on the brand and model of lift you purchased. The following steps will help you assemble your new lift in no time at all. To start, unpack the lift from its packaging. Install the cables and chains, if applicable try it now>>. Once the cables and chains are installed, set up the garage door opener and adjust the slack safety lock.

Installing the columns

There are a few things to keep in mind when installing the columns of a four-post car lift. First, make sure the column is 90 degrees vertical across. Next, you should add shims to level the columns. Once you have the columns leveled, you can install the offside or power side columns of the lift. Remember to tighten the anchors and use a level to ensure they stay level.

When installing the columns of a four post car lift, first ensure the floor is stable enough to support the columns. Most manufacturers recommend six to twelve inches of concrete depth and a PSI of at least 3000. Once the columns are in place, the rest of the lift is easy to install. After installing the columns, make sure to remove all packaging materials. If you are using a forklift, you can lift the top trough with two ladders. Then, tighten the top trough to ensure that the columns are secure. The installation process is not difficult, but it does require six or more strong friends to ensure it stays upright.

Installing the cables

When installing the cables of a 4 post car lift, remember that the cables must be tightened properly. This is especially important because improperly tightened cables may damage the seals on the cylinder rod, which will result in fluid leakage. To avoid this problem, follow the maintenance instructions that came with your lift. Once the cables are tightened, check the cable tension and adjust it as necessary. Make sure that the cable tension is even from one end of the carriage to the other.

The cables of a four post car lift must be installed correctly so that the carriages travel at the same level. Check the cables by lifting the carriage and checking that they are even. In addition, the cables must be properly adjusted to keep the carriages level during lifting and lowering. Read the manual carefully to make sure they are installed properly. Once the cables have been installed properly, you can install the lift.

Adjusting the slack safety lock

The first step in adjusting the slack safety lock on if a four-post car lift is to adjust the cable tension. The cables that provide tension to the cylinder rod must be set correctly. The cables should be tightened in equal amounts on both sides of the lift's carriage. To get the proper tension on the cable, tighten the cables on both sides of the carriage, alternately tightening up one side and loosening the other.

Next, adjust the slack safety lock. This feature is typically found on professional-grade car lifts. This feature acts as an automatic brake on the lift's support structure, reducing the risk of sudden free fall. Make sure that the locks are spaced at least five inches apart so that they do not rub against one another. Adjusting the slack safety lock is crucial for safe lifting of cars.

Setting up the jackshaft garage door opener

A jackshaft garage door opener is mounted on the wall next to the garage door. It replaces the overhead track system and connects to the shaft where the springs are mounted. It works on both standard and high-lift doors and requires an electrical outlet within six feet of the opener. The opener's primary function is to open and close the garage door, and it can work with either type.

Once the jackshaft garage door opener is installed, a cable tension monitor must be attached to the cable. The cable must extend about an eighth of an inch beyond the drum. The cable should be installed at least six inches above the mounting surface, and the bell wire should be run over and around the torsion bar, connecting to the green quick-connect terminal. When mounting the wall remote, it is a good idea to mount it five feet off the floor. The white and red wires should be run to the opener and positioned high enough to prevent children from accidentally tripping over them.